looking for suitable laboratory equipment?

Our professionals are available 24*7. You can call us any time.

To understanding
Bulk Specific gravity and Water Absorption of Aggregate

Bulk Specific gravity and Water Absorption of Aggregate

2.2 Bulk Specific Gravity—Bulk specific gravity is the ratio of the oven-dry weight of the aggregate to the bulk volume of the aggregate particles. 3. APPARATUS 3.1 Balance, Class G2, in accordance with Tex-901-K, with a minimum capacity of 10,000 g. 3.2 Glass jar, 2 L (0.5 gal.), and pycnometer cap.

More Product
ACI METHOD OF PROPORTIONING CONCRETE MIXES

ACI METHOD OF PROPORTIONING CONCRETE MIXES

Aggregate weights. Aggregate volumes are calculated based on oven dry unit weights, but aggregate is typically batched based on actual weight. Therefore, any moisture in the aggregate will increase its weight and stockpiled aggregates almost always contain some moisture. Without correcting for this, the batched aggregate volumes will be incorrect.

More Product
More On Adjusting for Aggregate Moisture - Concrete Construction

More On Adjusting for Aggregate Moisture - Concrete Construction

Aug 23, 2007 On this project the concrete tickets showed sand moisture content of 3.5% (soaking wet). To the testing company and engineer that meant a total water weight of 3.5% times the oven-dry weight of the sand. The amount of water on the surface of the aggregate would be computed as 3.5% minus the absorption multiplied by the oven-dry weight.

More Product
Oven Dry For Aggregate

Oven Dry For Aggregate

Density of Cement Sand and Aggregate Bulk ... - Civil Lead. Absolute Specific Gravity = (Weight of oven-dried aggregate at 100c for 24 hours) / (Weight of water’s volume equal to that of aggregate’s solids excluding pores) Essential Points Most of the aggregates possess a relative density within 2.4 – 2.9 with a similar particle density about 2400-2900 Kg/m 3 ( 150-181 lb/ft 3 ).

More Product
Lab Report Specific Gravity and Absorption of Fine Aggregates

Lab Report Specific Gravity and Absorption of Fine Aggregates

Dry the fine aggregates by placing it in the oven or sun drying and wait until completely dried. Take and record the weight for sun-dried condition. DATA AND RESULTS. Recorded measurements and observations. Fine Aggregate (sample) (SSD) WSSD (SUBMERGED) Wsub (SUN-DRIED) WSD. A 500 g 200 g 460 g B 500 g 160 g 480 g C 500 g 240 g 480 g. …

More Product
Oven Dry Aggregates

Oven Dry Aggregates

Here, for coarse aggregates, the standard test method has been explained in ASTM C 127(AASHTO) and for fine aggregates, the standard test method has been explained in ASTM C 128 (AASHTO). [3] The relative density of an aggregate can be determined on an oven-dry basis or a saturated surface-dry (SSD) basis. Get Details

More Product
dolomite aggregate oven dry -

dolomite aggregate oven dry -

Inspection Sampling Procedures for Fine Coarse , Know More. 205 Acceptance Procedures for Dolomite Aggregates 206 Scratch Hardness of Coarse Aggregate Particles , Laboratory oven capable of maintaining a temperature of 230 177 9 176 F, , Oven -- for drying samples after reduction 3 Cooling rack and fan -- for cooling samples when dry note make sure

More Product
Aggregate: Mechanical Properties of Aggregate Concrete Technology

Aggregate: Mechanical Properties of Aggregate Concrete Technology

Let the weight of oven dry sample in the cup = W kg. Weight of aggregate passing 2.36 mm sieve = W 1 kg. Then impact value = [(W 1 /W) x 100] ... It has been observed that absorption of water by dry aggregate slows down due to the coating of particles with cement paste. The water absorption by aggregate should be determined for 10 to 30 minutes ...

More Product
Experiment (1) Total Moisture Content Objective

Experiment (1) Total Moisture Content Objective

Moisture States of Aggregates: Oven-dry (OD): All moisture is removed from the aggregate by heating in an oven at 105c to constant weight all pores are empty. .اغارفلا لخاد لاو حطسلا يلع بوطر ذجوي لا Air-Dry(AD): All the moisture is removed from the surface, but internal pores are partially full.

More Product
How To Do Sieve Analysis Of Aggregate

How To Do Sieve Analysis Of Aggregate

Nov 09, 2014 Put the oven to a temperature of 110 degree Celsius. Once the sample is oven dried, weigh the sample, mark as Mass at Dry condition, or M2. 5. Sieving the sample. The sieves number that you will use in the 20 size aggregate samples are 37.5 mm, 20.0 mm, 14.0 mm, 10.0 mm 0.075 mm. Place the bigger size of sieve on top of smaller and in order ...

More Product
PowerPoint Presentation

PowerPoint Presentation

Since the as-used moisture content is greater than the absorption for each aggregate, each aggregate contributes the excess water to the mix, thus reducing the water that must be added to mix. The water added to the mix is the water computed for oven-dry aggregates (305 Ib/yd1) plus the excess water in each aggregate. 221.61b/yd3

More Product
Soil aggregate stability - Wikipedia

Soil aggregate stability - Wikipedia

Soil sieve nests after removal from the oven with dry soil aggregates Soil aggregate stability is a measure of the ability of soil aggregates to resist degradation when exposed to external forces such as water erosion and wind erosion , shrinking and swelling processes, and tillage (Papadopoulos, 2011; [1] USDA, 2008 [2] ).

More Product
civil engineering mcqs with answers - concrete technology

civil engineering mcqs with answers - concrete technology

the weight of oven dry aggregate divided by its absolute volume, including the natural pores in the aggregate particles. C. the weight of aggregate required to fill a container of unit volume. D. the difference in weight of the aggregate in saturated surface dry condition and in moist condition. Answer Explanation. Answer: Option A. Explanation:

More Product
Specific Gravity and Water Absorption Tests on Aggregates

Specific Gravity and Water Absorption Tests on Aggregates

Then the aggregates are transferred to the second dry cloth spread in single layer and allowed to dry for at least 10 minutes until the aggregates are completely surface dry. The surface dried aggregate is then weighed = W 3 g; The aggregate is placed in a shallow tray and kept in an oven maintained at a temperature of 110 C for 24 hrs.

More Product
Latest News
X

CONTACT US

If you are interested in our products, please contact us, your satisfaction is our eternal pursuit!